Try Cisco 200-601 Exam Questions – Updated 2017

By | December 5, 2017

Are you having difficulties looking for reliable 200-601 exam preparation materials for Cisco 200-601 exam Certification Exam? Don’t look any further. We are here to offer you the only review 200-601 exam questions that can guarantee your success in 200-601 exam. It is our commitment to being the sole provider of Cisco Network Application Development 200-601 exam test preparation materials for every IT professional. All Cisco 200-601 exam dumps preparation material prepared by the subject matter experts who formulate, evaluate, and update our products.

Version: 9.0
Question: 1

A ProfiNET management system operator is unable to see diagnostic information for a Cisco Industrial Ethernet switch that has been added to a SIMATIC management station. Based on the provided CLI output, which statement is correct?
switch# show profinet status
State : Enabled
Vlan : 201
Id : IE2000-Switch
Connected : Yes
ReductRatio : 128
GSD version : Mis-match

A. The assigned ProfiNET VLAN is not valid and should be less than 100
B. LLDP has been disabled on this switch
C. The GSD file version on the switch does not match the GSD file version on the management station
D. The Reduction Ration has been set too low

Answer: C

Question: 2

A ProfiNET management system operator is unable to add a ProfiNET Conformance Class B device to a SIMATIC management station. The device is connected to interface FastEthernet1/3. Based on the provided CLI output, which statement is correct?
switch#show profinet lldp
Fa1/1 port-003-00000 On
Fa1/2 port-004-00000 On
Fa1/3 port-005-00000 Off
Fa1/4 port-006-00000 Off
Fa1/5 port-007-00000 On
Fa1/6 port-008-00000 Off
Fa1/7 port-009-00000 On
Fa1/8 port-010-00000 Off

A. LLDP has been disabled on this switch
B. The connected device is not sending LLDP packets with ProfiNET extensions
C. The port label needs to be changed on interface FastEthernet 1/3 to “port-003-00000”
D. ProfiNET is disabled on this switch

Answer: B

Question: 3

New Updated 200-601 Exam Questions 200-601 PDF dumps 200-601 practice exam dumps: https://www.dumpsschool.com/200-601-exam-dumps.html(70 Questions)

Refer to the exhbit. Which three elements would enable high availability and predictable performance for a motion control application spread across two switches (with video and I/O traffic)? (Choose three)

A. Configure QoS to give PTP traffic the highest priority
B. Fiber optic uplinks
C. Redundant uplinks
D. Configure QoS to give I/O traffic the highest priority
E. Copper uplinks
F. Interconnect the two switches

Answer: A, B, C

Question: 4

You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on?
A: Lattency and Jitter
B: Redundancy and high availability
C: Explicit and Implicit messaging
D: This cycle time is not possible on an Ethernet network
E: Gigabit port speed
Answer: A

Question: 5
Refer to the exhibit.

CIP Implicit messages from I/O#1 are being marked IP DSCP 47 by the endpoint and this marking is trusted by L2SW4. L2SW4 is configured to map DSCP 47 to output queue 1 threshold 1. You have received feedback that some of these messages are not being received. Executing the show mls interface GigabitEthernet statistics command on L2SW4 results in:
L2SW4# show mls interface GigabitEthernet 1/1 statistics

output queues dropped:
queue: threshold1 threshold2 threshold3
queue 0 0 0 0
queue 1 309232345 450 0
queue 2 300 10 0
queue 3 91 0 0
Repeating this command results in the counters incrementing for queue 1 threshold 1. What are two options for reducing the packet loss on this interface while preserving the end-to-end DSCP marking? (Choose two)

A. Configure I/O#1 to mark this traffic with a different DSCP that is mapped to a less congested queue
B. Increase the buffer allocation for input queue 1
C. Increase the buffer allocation for output queue 1
D. Alter the service policy to police to a higher CIR
E. Change the egress queue map on L2SW4 to map this traffic to a less congested queue

Answer: C, E

Question: 6

It is common to use Resilient Ethernet Protocol (REP) on the manufacturing floor as a resiliency protocol, as opposed to the Enterprise where it is not generally deployed. What are two reasons why REP is more suitable for the plant floor? (Choose two)

A. REP is only supported on Industrial Ethernet switches, it is not supported on Catalyst switches.
B. REP converges faster than Spanning Tree, allowing for greater network availability.
C. REP supports Industrial Ethernet protocols better because it moves the packets faster.
D. Running dual cables from access switches to an aggregation switch can have a much higher cost on the plant floor than in the Enterprise and running a ring protocol like REP provides resiliency at a lower cost.
E. Industrial protocols can be negatively impacted by the number of nodes the Ethernet frame traverses, REP provides a topology with no more than 3 nodes for any data path.

Answer: B, D

         

Facebook Comments