Try NetApp NS0-180 Exam Questions – Updated 2017

By | December 5, 2017

Are you having difficulties looking for reliable NS0-180 exam preparation materials for NetApp NS0-180 exam Certification Exam? Don’t look any further. We are here to offer you the only review NS0-180 exam questions that can guarantee your success in NS0-180 exam. It is our commitment to being the sole provider of NetApp IT Fundamentals NS0-180 exam test preparation materials for every IT professional. All NetApp NS0-180 exam dumps preparation material prepared by the subject matter experts who formulate, evaluate, and update our products.

Version: 9.1
Question: 1

You are asked to install a 6-node cluster of FAS8080 controllers. The installation has been completed and Config Advisor shows no warnings or errors. The customer can ping and access the controller.
Which statement is true in this scenario?

A. This installation has not been completed successfully until you have confirmed that SSH is enabled.
B. This installation has not been completed successfully until the customer and NetApp Support have received a minimum of three AutoSupport messages.
C. This installation has been completed successfully only if you have confirmed that the configuration is correct.
D. This installation has been completed successfully, because Config Advisor would identify the missing configuration.

Answer: C

Config Advisor is a configuration validation and health check tool. It is used to check for common configuration errors. You can use the Config Advisor tool to verify that the cluster is cabled correctly. After Config Advisor indicates that no errors is found, you must complete protocol configuration and verify cluster setup.
Reference: Clustered Data ONTAP 8.3, Express Setup Guide for 80xx Systems, page 33

Question: 2

When you create a single-node cluster, which statement is correct about the cluster base license key?

A. A single-node cluster does not need any cluster-base license key.
B. A single-node clustered Data ONTAP 8.1 license key is seven characters long.
C. Clustered Data ONTAP 8.2 and 8.3 license keys are 14 characters long.
D. A single-node cluster requires a cluster base key to use a cluster.

Answer: D

A Cluster Base Key required to create a Single-Node Cluster.
Incorrect: Not A: A single-node Cluster requires a Cluster Base Key to run the create cluster command. Not B: Clustered ONTAP 8.1 license keys are fourteen (14) characters long.
Reference: FAQ – Data ONTAP Licensing

Question: 3

New Updated NS0-180 Exam Questions NS0-180 PDF dumps NS0-180 practice exam dumps: Questions)

What happens to the NTP configuration in clustered Data ONTAP 8.3 when a node joins a cluster?

A. A node that joins a cluster has a separate NTP service.
B. A node that joins a cluster automatically adopts the NTP configuration of the cluster.
C. A node that joins a cluster must be manually configured in the NTP.
D. A node that joins a cluster must reboot before running the NTP service.

Answer: B

A node that joins a cluster automatically adopts the NTP configuration of the cluster.
Reference: How to configure and troubleshoot NTP on clustered Data ONTAP 8.2 and later using CLI

Question: 4

You are assigned to install five DS2246 with twenty-four 400 GB SSDs per shelf to a single node system.
According the NetApp, which statement is correct?

A. You cannot install five SSD shelves to one System.
B. You need at least two stacks.
C. You need at least three stacks.
D. You can put all shelves in one stack.

Answer: D

Up to 10 shelves are supported per stack for the DS2246, so we one stack is enough as we only have five shelves (DS2246s).
Reference: Making the Move from FC to SAS Storage

Question: 5

Which three types of interface groups are supported on NetApp storage systems? (Choose three.)

A. single mode
B. HA interconnect
C. IPspaces
D. static multimode
E. dynamic multimode

Answer: A,D,E

You can create three different types of interface groups on your storage system: single-mode, static multimode, and dynamic multimode interface groups.
Reference: Types of interface groups

Question: 6

You have just configured the customer’s first SVM with a LIF IP The customer’s DNS IP address is and you are unable to ping it from the NetApp storage system, but you are able to ping the gateway and everything else works.
In this scenario what is the problem?

A. You need to have the DNS server on the same subnet as the LIF IP address.
B. You need to add a static gateway to the LIFs routing group.
C. You need to have the customer check the cable.
D. You need to add an IPspace and domain broadcast to the port.

Answer: D

A broadcast domain resides in an IPspace, and it contains a group of network ports, potentially from many nodes in the cluster, that belong to the same layer 2 network. The ports in the group are used in an SVM for data traffic.
Reference: Clustered Data ONTAP 8.3, Network Management Guide, page 8


Facebook Comments